自干型耐汽油玻璃油墨

1、?適用材質：金屬、電鍍、氧化鋁、電解板、鋁塑板、噴（烤）漆、噴塑、PA塑料尼龍、電木、玻璃鋼、密胺等。

2、?產品特性：半光、免烘烤、耐酒精、耐沖壓。

3、?稀釋劑：本公司B-03稀釋劑或783慢干稀釋劑。

4、?固化劑：本產品為單組份油墨，如有特殊要求也可選擇添加固化劑增加附著力及墨層抗性。

5、?油墨調配：充份攪拌后取所需用量進行調配使用，雙組份油墨先按比例添加固化劑攪拌均勻，然后再添加稀釋劑稀釋到合適粘度進行印刷；添加固化劑后的油墨超過使用時限會產生粘稠膠化現象，請及時清洗網版，并棄用油墨，不可回收。

6、?網版及刮膠：適合80T-140T（200目-350目）聚脂網紗，聚氨脂PU油性刮膠。

7、?干燥條件及時間：本產品可以常溫干燥，也可以烘烤快速干燥，建議干燥溫度及時間為25℃/24小時，60℃/40分鐘，80℃/30分鐘，100℃/20分鐘。

8、?性能檢測：
用3M600膠帶劃百格測試100%無脫落；
用棉布沾95%工業酒精以500G力水平來回擦拭100次無脫色；
1mm厚鋁片在印刷位置進行沖斷、卷邊、延壓后邊緣位置100%無脫落；

9、?包裝規格：1KG/膠罐，12罐/箱。

10、儲存條件：置于干燥通風處常溫保存；避免高溫、太陽直射，嚴禁煙火。

11、注意事項：請向我司索取《MSDS安全使用手冊》，并按指引進行安全生產。?
1,?applicable?materials:?metal,?electroplating,?alumina,?electrolytic?plate,?aluminum?plate,?spray?paint,?spray?(baked),?PA?nylon,?bakelite?plastic,?glass?steel,?melamine?etc..

2,?product?characteristics:?half?light,?no?baking,?alcohol?resistance,?stamping.

3.?Diluent:?the?company's?B-03?diluent?or?783?slow?dry?diluent.

4,?curing?agent:?This?product?-?ink,?if?there?are?special?requirements?can?also?choose?to?add?curing?agent?to?increase?adhesion?and?ink?layer?resistance.

5,?ink?deployment:?fully?mixing?after?the?dosage?required?for?the?deployment,?two-component?ink?first?adding?curing?agent?according?to?the?proportion?of?mixing?evenly,?then?add?the?diluent?to?the?appropriate?viscosity?of?printing?ink;?curing?agent?is?added?after?more?than?the?use?of?time?will?produce?viscous?gel?phenomenon,?please?clean?the?screen,?and?abandoned?ink?Unrecyclable.

6,?screen?and?frictioning:?for?80T-140T?(200?-350?mesh)?polyester?mesh,?polyurethane?PU?oily?frictioning.

7,?drying?conditions?and?time:?This?product?can?be?dried?at?room?temperature?or?dry?quickly.?It?is?recommended?that?the?drying?temperature?and?time?should?be?25?/24,?60?/40,?80?/30,?100?/20.

8.?Performance?testing:
Use?3M600?tape?to?make?100?lattice?tests?100%?without?falling?off.
With?cotton?cloth,?95%?industrial?alcohol?was?wiped?back?and?forth?at?the?level?of?500G?force?for?100?times?without?decolorization.
The?position?of?1mm?thick?aluminum?sheet?in?the?printing?position?is?broken,?curling,?and?the?edge?position?after?the?pressure?is?100%?without?falling?off.

9,?packaging?specifications:?1KG/?glue?cans,?12?cans?/?boxes.

10.?Storage?conditions:?keep?at?room?temperature?in?the?dry?and?ventilated?place;?avoid?high?temperature,?direct?sunlight,?and?strictly?prohibit?fireworks.

11,?attention:?please?ask?our?department?"MSDS?safety?manual"?and?carry?out?safety?production?according?to?the?guidelines.